Thermoplastic Composites
High-performance continuous fiber reinforced prepregs and consolidated sheets
Thermoplastic Composites
Product Overview
High-performance continuous fiber reinforced prepregs and consolidated sheets
Thermoplastic composites combine continuous fiber reinforcement with engineering or high-temperature thermoplastic matrices. The portfolio focuses on unidirectional prepreg tapes and consolidated sheets/laminates for fast, repeatable and highly automated composite manufacturing.
Request a Quote
Advantages & Product Forms
Key Advantages
- No curing reaction - consolidation by heat and pressure.
- Short processing cycles compared with thermoset prepregs.
- Excellent impact, fatigue and damage tolerance.
- High chemical and corrosion resistance.
- Weldable and thermoformable.
- Suitable for AFP, ATL, winding and compression molding.
- Long-term storage without conventional thermoset prepreg freezer requirements.
- Potential for reprocessing and recycling.
Product Forms
- UD Prepreg Tape — Carbon Fiber — PEEK / PAEK / PEKK / PPS / PEI / PA6 / PA12 / PC
- UD Prepreg Tape — Glass / Basalt Fiber — PEEK and selected matrices
- Fabric Prepreg — Carbon / Glass Fiber — PEEK
- Consolidated Sheet — Continuous Carbon Fiber — PEEK
- Consolidated Sheet — Continuous Glass Fiber — PEEK
- Reinforced Thermoplastic Sheet — Carbon fabric / felt — PEEK / PPS / PPSU / PEI / TPI
UD Prepreg Tapes
UD Thermoplastic Prepreg Tapes
Continuous fiber reinforcement for automated and high-rate processing
UD thermoplastic prepreg consists of continuous reinforcement fibers impregnated with a thermoplastic matrix. Fibers are aligned predominantly in one direction, allowing laminate stiffness and strength to be tailored through ply orientation and stacking sequence. Representative supplier tape widths are approximately 2–300 mm.
Matrix Systems
- PEEK — CF/BF — 350–400°C
- PAEK — CF — 320–350°C
- PEKK — CF — 370–400°C
- PPS — CF — 300–330°C
- PEI — CF — 320–360°C
- PA6 — CF — 240–280°C
- PA12 — CF — 200–230°C
- PC — CF — 200–240°C
*Representative supplier processing ranges; final parameters depend on product configuration and equipment.
Representative UD Tape Data
- Carbon fiber: T700 / T800 class options
- Fiber areal density: 145 g/m²
- Prepreg areal density: 220 g/m²
- Resin content: 34 ± 3%
- Single-ply thickness: 0.14 ± 0.02 mm
Manufacturing, Sheets & Laminates
Manufacturing
Automated Tape Laying (ATL) • Automated Fiber Placement (AFP) • Filament Winding • Compression Molding • Hot Press Consolidation • Continuous Lamination
Thermoplastic Composite Sheets & Laminates
Pre-consolidated materials for structural, machined and thermoformed components
Thermoplastic composite sheets are supplied as pre-consolidated laminates, combining continuous reinforcement with the processing advantages of thermoplastic polymers. They can be machined directly or subsequently thermoformed, welded or consolidated into larger structures.
Main Systems
- CF/PEEK — continuous carbon fiber — aerospace, medical, industrial
- GF/PEEK — continuous glass fiber — radomes, electrical, aerospace
- CF Fabric/PEEK — balanced in-plane properties — structural panels and machined parts
- CF/PPS — chemical resistance and efficient processing
- CF/PPSU — toughness and temperature resistance
- CF/PEI — high-temperature performance
- CF/TPI — advanced high-temperature structural applications
CF/PEEK Representative Laminate Data
- Fiber areal density: 285 g/m²
- Prepreg areal density: 485 g/m²
- Resin content: 42 ± 3%
- Density: 1.55 g/cm³
- Tensile strength 0°: 740 MPa
- Tensile modulus 0°: 60 GPa
- Flexural strength 0°: 950 MPa
- Flexural modulus 0°: 58 GPa
- Compression strength 0°: 620 MPa
Representative Sheet Dimensions
380 × 240 mm • 440 × 380 mm • 1000 × 600 mm • 1200 × 600 mm • 1100 × 1000 mm • Custom sizes available
Processing & Applications
PROCESSING & APPLICATIONS
Manufacturing Route
From thermoplastic prepreg to finished high-performance component
UD Tape / Fabric Prepreg → Lay-up / AFP / ATL / Winding → Heat & Consolidation → Controlled Cooling → Thermoforming / Welding / Machining → Finished Component
Processing Methods
- AFP / ATL — automated structural lay-up
- Filament Winding — tubular and axisymmetric structures
- Hot Press Consolidation — flat sheets and structural laminates
- Compression Molding — net / near-net shape components
- Thermoforming — forming consolidated sheets
- CNC Machining — precision finished components
- Thermoplastic Welding — joining without conventional adhesives
Application Areas
- Aerospace & UAV — brackets, fuselage components, supports, stiffeners, frames and lightweight structures.
- Medical — radiolucent components, bone plates and surgical instruments.
- Automotive & Transportation — lightweight structures, brackets and energy-management components.
- Industrial & Energy — wear components, pump/compressor parts, electrical insulation and chemically resistant structures.
Why Thermoplastic Composites
FAST PROCESSING • HIGH TOUGHNESS • AUTOMATION READY • RE-FORMABLE • WELDABLE • HIGH PERFORMANCE
Contact
Discuss your composite manufacturing requirements.
Tell us about your material, equipment or tooling requirements.
- Abu Dhabi, Al Majarat St, Al Danah, UAE
- +971 58 538 6625
- sales@h-composites.com